craftmaster hot water heater manual

craftmaster hot water heater manual

Page Count: 16 We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Important Safety Instructions CAUTION: Hydrogen gas is produced in a hot water system served by this heater that has not been used for a long period of time (2 weeks or more). Hydrogen is extremely flammable. To reduce the risk of injury under these conditions, it is recommended that the hot water faucet be opened for several minutes at the kitchen sink before using any electrical appliance connected to the hot water system. When hydrogen is present, there will be an unusual sound such as air escaping through the pipe as the water begins to flow. There should be no smoking or open flame near the faucet at the time it is open. The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of potential exposure to such substances. Warning: This product contains a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm. This appliance can cause low-level exposure to some of the substances listed, including formaldehyde. 2 In the absence of local code requirements, follow the regulations set forth in the latest edition of The National Electric Code, NFPA 70.http://nozhi-dick.ru/userfiles/canon-eos-5d-camera-manual.xml

• 1.0.

This is available from the following: National Fire Protection Agency 1 Batterymarch Park Quincy, MA 02269 American National Standards Institute 1430 Broadway NewYork, NY 10018 Check your phone listings for the local authorities having jurisdiction over your installation. Consumer Responsibilities This manual has been prepared to acquaint you with the installation, operation and maintenance of your electric water heater and to provide important safety information in these areas. We urge you to read all of the instructions thoroughly before attempting the installation or operation of this water heater. This manual should be kept for future reference. The manufacturer of this water heater will not be liable for any damages caused by failure to comply with the installation and operating instructions outlined in this manual. If you lack the necessary skills required to properly install this water heater or you have difficulty following the directions, you should not proceed but have a qualified person perform the installation of this water heater. Massachusetts code requires this water heater to be installed in accordance with Massachusetts Plumbing and Fuel Gas Code 248 CMR section 2.00 and 5.00. A data plate identifying your water heater can be found adjacent to the element door. When referring to your water heater always have the information listed on the data plate readily available. Retain your original receipt as proof of purchase. Unpacking the Water Heater Excessive Weight Hazard Use two or more people to move and install water heater. Failure to do so can result in back or other injury.It must be installed indoors and in a vertical position on a level surface. The water heater should be located in an area not subject to freezing temperatures. Water heaters located in unconditioned spaces (i.e., attics, basements, etc.) May require the water piping and drain piping to be insulated to protect against freezing.http://www.adishaktiyogacentre.com/UserFiles/canon-eos-5d-mark-ii-manual-video-control.xml

The drain and controls must be easily accessible for operation and service. Do not use this water heater in conjunction with a spa or hot tub. Note: Local codes and requirements in your area may require the installation of your water heater be accomplished in a way that the bottom element is elevated from the floor at least 18 inches. Important: The water heater should be located in an area where leakage of the tank or connections will not result in damage to the area adjacent to the water heater or to lower floors of the structure. Due to the normal corrosive action of the water, the tank will eventually leak after an extended period of time. It is recommended that a suitable drain pan be installed under the water heater as shown below. This pan is to protect the property from damage which may occur from normal condensate formation on the tank or leaks in the tank and pipe connections. Locate the water heater near a suitable indoor drain. Outside drains are subject to freezing temperatures which can obstruct the drain line. Note: The water heater shall be located so it is not subject to physical damage by moving vehicles or area flooding. Contact local utilities for code requirements in your area or call 1-800-999-9515 and request instructions. 4 Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Fire Hazard Use proper size solid copper Wl re. Use a UL approved strain relief. Connect ground wire to green ground screw. Failure to do so can result in death, fire, or electrical shock. If you lack the necessary skills required to properly install the electrical wiring to this water heater, do not proceed but have a qualified electrician perform the installation. Always reference the wiring diagram located on the water heater for the correct electrical connections. When installing the electrical wiring to the water heater: 1. Be sure tank is completely filled with water before making any electrical connections.

(See Figure 2) 2. Shut-off the power to the unit. 3. Loosen the screw holding the junction box cover to the top of the water heater. Set the cover aside. 4. Connect the electrical supply to the water heater in accordance with local utility requirements and codes. The manufacturer will not warranty any elements damaged in this manner.If the indoor installation area is subject to freezing temperatures, the water piping must be protected by insulation. Water supply pressure should not exceed 80% of the working pressure of the water heater. The working pressure is stated on the water heater's data plate. If this occurs a pressure limiting valve with a bypass may need to be installed in the cold water supply line. This should be placed on the supply to the entire house in order to maintain equal hot and cold water pressures. Important: Heat cannot be applied to the water fittings on the heater as they may contain nonmetallic parts. If solder connections are used, solder the pipe to the adapter before attaching the adapter to the hot and cold water fittings. Important: Some models may contain energy saving heat traps to prevent the circulation of hot water within the pipes. Do not remove these inserts. 2. The installation of unions in both the hot and cold water supply lines are recommended for ease of removing the water heater for service or replacement. 3. The manufacturer of this water heater recommends installing a tempering valve in the domestic hot water line as shown in Figures 7 and 8. These valves reduce the point-of-use temperature of the hot water by mixing cold and hot water and are readily available. It should be located close to the water heater and be easily accessible. To purge the lines of any excess air and sediment, keep the hot water faucet open for 3 minutes after a constant flow of water is obtained. Close the faucet and check all connections for leaks.

The system should be installed only with new piping that is suitable for potable (drinkable) water such as copper, CPVC, or polybutylene. DO NOT use PVC water piping. DO NOT use any pumps, valves, or fittings that are not compatible with potable water. DO NOT use valves that may cause excessive restriction to water flow. Use full flow ball or gate valves only. DO NOT tamper with the thermostat, heater elements, electrical connections, or temperature and pressure relief valve. Tampering voids all warranties. Only qualified technicians should service these components. DO NOT use with piping that has been treated with chromate's, boiler seal, or other chemicals. DO NOT add any chemicals to the system piping which will contaminate the potable water supply. The water utility supply meter may contain a check valve, backflow preventer or water pressure reducing valve. This will create a closed water system. During the heating cycle of the water heater, the water expands causing pressure inside the water heater to increase. This may cause the temperature and pressure relief valve to discharge small quantities of hot water. To prevent this from happening, there are two recommendations:, Install a diaphragm-type expansion tank that is suitable for potable water on the cold water supply line. The expansion tank must have a minimum capacity of 1.5 U.S. gallons for every 50 gallons of stored water. 2. Install a 125 PSI pressure relief valve in the cold water supply line. Make sure the discharge of this valve is directed to an open drain and protected from freezing. Contact the local water supplier or plumbing inspector for information on how to control this situation. Do not plug the temperature and pressure relief valve. Temperature and Pressure Relief Valve Explosion Hazard If the temperature and pressure relief valve is dripping or leaking, have a licensed plumber repair it. Do not plug valve. Do not remove valve.

Failure to follow these instructions can result in death, or explosion. Caution: To reduce the risk of excessive pressures and temperatures in this water heater, install temperature and pressure relief protective equipment required by local codes, but no less than a combination temperature and pressure relief valve certified by a nationally recognized testing laboratory that maintains periodic inspection of the production of listed equipment or materials, as meeting the requirements for Relief Valves and Automatic Shutoff Devices for Hot Water Supply Systems, ANSI Z21.22 - 1986. This valve must be marked with the maximum set pressure not to exceed the marked maximum working pressure of the water heater. Install the valve into an opening provided and marked for this purpose in the water heater, and orient it or provide tubing so that any discharge from the valve exits only within 6 inches above, or at any distance below, the structural floor, and does not contact any live electrical part. The discharge opening must not be blocked or reduced in size under any circumstance. Do not use an oldor existing valve as it may be damaged or not adequate forthe working pressure of the new water heater. Do not place anyvalve between the relief valve andthe tank. Must be installed to allow complete drainage of both the valve and discharge line. Electrical Connections Wiring and connections comply with all applicable codes. Water heater and electrical supply are properly grounded. Proper overload fuse or circuit breaker protection installed. Immediately call a qualified service technician to inspect the water heater and replace any thermostat or insulation that has been exposed to water. Do not attempt to repair these parts. Water heaters subjected to flood conditions or any time the thermostat(s) have been submerged in water require replacement of the entire water heater. The high limit control can be reset by firmly pushing in the red reset button located on the thermostat.

Children, disabled and elderly are at highest risk of being scalded. See instructions manual before setting temperature at water heater. Feel water before bathing or showering. Temperature limiting valves are available. If hot water use is expected to be more than normal, a higher thermostat setting may be required to meet the increased demand. When leaving your home for extended periods (vacations, etc.) turn the thermostat to its lowest setting. This will maintain the water at low temperatures with minimum energy losses and prevent the tank from freezing during cold weather. Upper and lower thermostats must be adjusted to the same temperature. Any other adjustments must be made by qualified service personnel. 1. Shut-off the power to the water heater. 2. Remove the access cover(s) and fold the insulation outward and away from the thermostat(s). Do not remove the plastic cover. 3. Using a screwdriver to adjust the thermostat pointer, set the thermostat(s) to the desired water temperature. Be sure the RED reset button (High Limit Control) is properly set: push in firmly to reset. 4. Replace the insulation. Make sure the thermostat(s) are well covered. Replace the access cover(s). 5. Apply power to the water heater.Once the anode is depleted, the tank will start to corrode, eventually developing a leak. Do not remove this rod permanently as it will void any warranties, stated or implied. The parts list includes a special anode that can be ordered if water odor or discoloration occurs. This rod may reduce but not eliminate water odor problems. The water supply system may require special filtration equipment from a water conditioning company to successfully eliminate all water odor problems. Artificially softened water is exceedingly corrosive because the process substitutes sodium ions for magnesium and calcium ions. The use of a water softener may decrease the life of the water heater tank.

The anode rod should be removed from the water heater tank every 3 years for inspection. If the rod is more than 50% depleted, the anode rod should be replaced. For replacing the anode, shut-off the power to the water heater. Be sure the cold water supply to the heater is turned off. Open the hot water faucet to depressurize the water tank. Drain out 5 gallons of water from the drain valve at the bottom of the heater. Remove the anode rod. Water Heater Sounds During the normal operation of the water heater, sounds or noises may be heard. These noises are common and may result from the following: 1. Normal expansion and contraction of metal parts during periods of heat-up and cool-down. 2. Sediment buildup in the tank bottom will create varying amounts of noise and may cause premature tank failure. Stacking Stacking occurs when a series of short draws of hot water (3 gallons or less) are taken from the water heater tank. This causes increased cycling of the heater elements and can result in increased water temperatures at the hot water outlet. An anti-scald device is recommended in the hot water supply line to reduce the risk of scald injury. Maintenance Temperature and Pressure Relief Valve Explosion Hazard If the temperature and pressure relief valve is dripping or leaking, have a licensed plumber repair it. Do not plug valve. Do not remove valve. Failure to follow these instructions can result in death, or explosion. Manually operate the temperature and pressure relief valve at least once a year to make sure it is working properly. To prevent water damage, the valve must be properly connected to a discharge line which terminates at an adequate drain. Standing clear of the outlet (discharged water may be hot), slowly lift and release the lever handle on the temperature and FIGURE 11 I TEMPERATURE AND PRESSURE I RELIEF VALVE DISCHARGE LINE TO DRAIN pressure relief valve to allow the valve to operate freely and return to its closed position.

If the valve fails to completely reset and continues to release water, immediately shut-off the electrical power and the cold water inlet valve and call a qualified service technician. 11 It is recommended that the tank be drained, and flushed every 6 months to remove sediment which may buildup during operation. To drain the tank perform the following steps: 1. Turn off the power to water heater. 2. Close the cold water inlet valve and open a nearby hot water faucet. 3. Connect a hose to the drain valve and terminate it to an adequate drain. Allow all the water to drain from the tank. Flush the tank with water as needed to remove sediment. 5. Close the drain valve, refill the tank, and restore power. If the water heater is going to be shut down for an extended period, the drain valve should be left open. NOTE: When draining Table Top models, remove the screw securing the drain access cover. Remove the cover by pulling down and away from the water heater. Heating Element Replacement Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Fold the insulation outward and away from the heater element(s). Remove the plastic thermostat cover from the thermostat(s) making sure to disengage the attachment point from the thermostat. 4. Disconnect the electric wires from the heating element (Figure 13). Remove the existing gasket. FIGURE 13 WIRES ELEMENT SCREWS,, Clean the area where the gasket fits to the tank. If you are replacing the bottom element, remove the accumulated sediment on the bottom of the tank. Make sure the replacement element has the correct voltage and wattage rating. Position the new gasket on the element and insert it into the water heater tank (Figure 14). Tighten the element by turning it clockwise until secure.

12 To purge the lines of any excess air and sediment, keep the hot water faucet open for 3 minutes after a constant flow of water is obtained. 8. Check for leaks around the element(s). 9. Connect the electric wires to the heater element. Make sure the wires are secure. Replace the plastic thermostat cover making sure the attachment points are engaged on the thermostat. 10. Replace the access cover(s). 11. Make certain the tank is filled with water. Applying electric current to heater elements not submerged in water will destroy them. 12. Restore the electric power supply to the water heater. Smith in Product Lines. Keep this manual in the pocket on heater for future reference whenever maintenance, Read this manual and the labels on the water heater before you install.US CRAFTMASTER Water us craftmaster water heater manual heater, Electric Manual Water heater, Electric US CRAFTMASTER (L) Related questions. Compton Products Company is a full service provider of your mobile home water heater needs. Save 5% with coupon. Manuals and User Guides for US CRAFTMASTER ES2J40RDV. Craftmaster Hot Water Heater Repair Part 1 Michael O'Brien how to diy fix a honeywell water heater temprature control valve with code 4 United States Restricted Mode: Off. Find a large selection of US Craftmaster at low Fleet Farm prices. Smith in Product Lines. Fully modulating, gas fired, tankless water heater specifically designed for residential and commercial applications. Fully modulating, gas fired, tankless water heater specifically designed for residential and commercial applications. Learn About Electric Water Heaters. The manufacturer and seller of this water heater will not be liable for any damages, injuries, or. Removing the Old Water Heater. Residenial Atmospheric Gas Water Heater with the Flame Guard Safety System. There are horror stories about these water heaters not working and finally being replaced with another brand.

What would cause my us craftmaster water heater manual Craftmaster water heater model e1 to not be as hot and run out of hot water. Do not discard this manual. Product Support Contact Us Need More Help. Craftmaster Water Heaters us craftmaster water heater manual are some of the most energy-efficient water heaters on the market. S. Learn About Gas Water Heaters. Download free electronic versions of our Whirlpool Water Heater care, use and installation instructions. Step 1 Before you make an adjustment to the water heater, check the temperature of the hot water as it comes out of a faucet closest to the water heater. There is no hot water. You or future users of this water heater will need it for future reference. Sold by DIY Repair Parts. SAVE money and repair it yourself. View online Installation and operation manual us craftmaster water heater manual for US CRAFTMASTER Water Heater or simply click Download button to examine the US CRAFTMASTER guidelines offline on your desktop or laptop computer. Maximum efficiency plus maximum hot water equals maximum savings. What to Do If It Leaks. Only 2 left in stock - order soon. There is a class action law suit against Whirlpool (made by US Craftmaster). Craftmaster Water Heaters are some of the most energy-efficient water heaters on the market. Craftmaster Hot Water Heater Repair Part 1 Michael O'Brien how to diy fix a honeywell water heater temprature control us craftmaster water heater manual valve with code 4 United States Restricted Mode: Off. User Manuals, Guides and Specifications us craftmaster water heater manual for your US CRAFTMASTER ES2J40RDV Water Heater. American us craftmaster water heater manual Water Heater Parts Instructions. U. Craftmaster. S. User manuals, Us craftmaster Water heater Operating guides and Service manuals. Installing the New Water Heater. Efficiency at its finest. Craftmaster produces a wide variety of high-efficiency electric and gas water heaters ranging in capacity from 30 to gallons.

I am trying to find the owners manual for a Whirlpool Not pulling water What should our humidity settings be at what the lowess temperature the dehumidifier ad25u. Removing the Old Water Heater. Retain your original receipt as proof of purchase. Craftmaster tankless water heaters supplies endless hot water at preset temperatures. We are here to help - over 20 genuine Us-Craftmaster repair and replacement parts that are hassle free and guaranteed to fit every time. We have a 50 gallon hot water tank and we have changed both elements us craftmaster water heater manual and the thermostat and it still won't give any hot water.s. Care Instructions, Support Resources. Installing the New Water Heater. Whirlpool Gallon BTU Short Natural Gas Water Heater Model BFG1FS3NOV Whirlpool Gallon BTU Tall Natural Gas Water Heater Model BFG1FT3NOV Whirlpool Gallon BTU Short Natural Gas Water Heater Model BFG1FS3NOV Envirotemp Gallon BTU Tall Natural Gas Water Heater. If you feel hesitate about the water heater that you have right now in your own house. GTNI - Non-Condensing Indoor Natural Gas Tankless Water Heater. Only natural gas water heaters sold under the following brand names are included in the recall: American Proline, Envirotemp, Mor-Flo, Powerflex, Premier Plus and US Craftmaster. Model number Digit product number 3. The reset button seems to be loose when I hold in down it doesn't pop back out. View online Installation and operation manual for US CRAFTMASTER Water Heater or simply click Download button to examine the US CRAFTMASTER guidelines offline on your desktop or laptop computer. Our Condensing models provide the highest energy efficiency, saving money in all applications. Troubleshooting us craftmaster Water Heaters. Product Support Contact Us Need us craftmaster water heater manual More Help. I us craftmaster water heater manual followed the instructions to light the pilot several times. How do us craftmaster water heater manual you stop a two.

But, there is another thing about this us craftmaster water heater manual thing that you need to know about its usages, you need to know about the US craftmaster water heater age. Us Craftmaster Water Heater Control Panel Assembly Genuine Original Equipment Manufacturer us craftmaster water heater manual (OEM) part. Get it as soon as Tue, Nov FREE Shipping by Amazon. Craftmaster Gas Tankless Product Tear Pad; Brochures. The serial number, located on the data plate on the front of the water heater, starts with through Did your Us-Craftmaster model ES2J65HDV water heater, electric break down. Residential Electric Water Heater. Craftmaster. Download 13 Us craftmaster Water Heater PDF manuals.S. Please contact us for your water heater requirements.Water Heater pdf manual download.